How to install and program Utilitec 0192773 Timer

Waterheatertimer.org

is a self-help website

Figure volts amps watts for water heater

9 Ways to save with a water heater

Do-it-yourself

See new water heating ideas 2010

Wire T1906 and T1905 timers

Wire T-101 T103 T104 timers

Wire EH40 and WH40 timers

Paragon timers and manuals
Tork TU universal timer

In-wall programmable timers
Leviton LPV25

2011

Other Utilitec timers:
Utilitec 0141224
Utilitec LW60418

Utilitec 0155671
Utilitec 0144506
Utilitec LW68424
Utilitec LW68465
Utilitec 149289

How to install and program

Utilitec LW60419 Timer / Utilitec 0192773 Timer

Support waterheatertimer.org and buy pdf manual for $4

Utilitec 0331645 manual
Utilitec TE08WHBL manual
Utilitec 0155671 manual
Utilitec TH06WHBL manual
Utilitec 0149289 manual
Utilitec 0358708 manual
Utilitec TM21DOLBL
Utilitec 03357930
Utilitec TMDW50L

Larger image

Utilitec LW60419 / Utilitec 0192773 / Lowes 0192773

Timer replaces on-off switch that has 2 wires (excluding ground).
If switch has 3 wires, then Utilitec is wrong timer.
To replace switch that has 3 wires, you need Aube T1032 see
If lights blink on and off after installing Utilitec timer, then you have connected the red wire and white wire to Load. Read instructions below.
If lights blink on and off after installing Intermatic EJ500 or ST01C, then red wire is connected where blue wire should be connected. Reverse red and blue wires.

Wiring instructions from manual.
Additional help

Manual says:
Timer-black-wire to Hot; Timer-red-wire to Load (lights)
Timer-white-wire to Neutral.
Heres what to do
1) Timer-green-wire connects to bare ground wire.
2) Switch has 2 wires. Take switch wires and connect them to timer-black-wire and timer-red-wire. Choose either one for now.
3) In back of electric box are white wires twisted together and covered with wire nut. Connect timer-white to these wires.
4) If electric box does not have white wires described above, then connect timer-white to bare ground, along with timer-green wire.
5) Turn on electricity, and push ON-OFF button. If lights come on, timer is wired correctly. If lights do not come on, then reverse timer-red and timer-black wires.

Review wiring:

Timer black wire connects to Hot
Timer red wire connects to Load (wire going to lights)
Timer white wire connects to Neutral [* if you don't have neutral wires, connect white wire to bare ground wire]
Timer green wire connects to bare ground wire

How to put on a wire nut:
Twist wire nut clockwise between fingers until very tight.
No copper wire should show once wire nut is on (except with bare ground wire)
Check that wires do not pull loose and nut will not fall off.

Daylight savings time map

Current time is set:
DST is ON
OFF means the Load (light, fan, motor) is OFF
WE is Wednesday
Time is 10:34PM

Rating:
General: 125 V ac, 60 Hz; 15 A, 1875W
Resistive: 125 V ac, 60 Hz; 15 A, 1875W
Tungsten (incandescent): 8 Amp, 125 VAC 1000 Watts;
Ballast (fluorescent): 8 Amp, 125 VAC;
Motor: 1/4 H.P., 125 VAC;

Program the timer
		Press PROG once and 1 ON displays Press PROG again and 1 OFF displays

Timer has soft blue display that lights up each time button is pushed.
Use paperclip and push & hold reset for a couple seconds if problem occurs.

Intermatic	Aube	ETW350
ST01C	Woods	EJ500
Leviton	Tork	Hagar
Power pack	GE

Water heater Box timers

Intermatic trippers and parts	Dayton	Sprinkler timers	Power pack
Wire T1906 and T1905 timers	Wire T-101 T103 T104 timers	Paragon timers and manuals	Westek box timers
Wire EH40 and WH40 timers	Tork timers and manuals	Troubleshoot intermatic	Sylvania timers
Wire GE 15207 timer	How to set analog timers	Intermatic GM series	Pool timers and manuals
GE box timers		Westinghouse timers Timex timers Brinks timers	3-phase timer

E-mail: info@waterheatertimer.org
Site map