![]() |
How
to convert energy smart water heater to ordinary water heater
Currently called 'heaters with electronic thermostat,' or 'electronic display.' Electronic thermostat spec sheet Electronic display spec sheet Energy smart was originally designed to integrate with smart grid, but smart grid module never materialized due to 'privacy concerns' and shortage of usable data. Smart grid products were overcome by wifi which offers usable data, but no privacy Search
waterheatertimer.org /
all results
|
Use only 600 volt wire. Lamp cord, extension cords are not rated 600 volt. Use copper wire only. Aluminum wire is fire risk and should be avoided or installed by professional. 30 amp breaker use 10 gauge / 120-240 volt 30 amp outlet can be installed on 30 amp breaker only/ use 10 gauge wire ... cannot be connected to 15-20-40 amp breaker. ![]() Orange/ #10 gauge wire, with ground ... 30 amp capacity. Safe maximum: 30 x 80% = 24 amps. Buy: 10-2 gauge/ 30 amp 10-3/ 30 amp Southwire electric tools |
Yellow
12 gauge 20 amp 120 volt 20 amp outlet can be installed on 20 amp breaker, but not 15 amp breaker/ use 12 ga wire. ... cannot be connected to 30-40 amp breaker. 1 ![]() Yellow/ #12 gauge wire, with ground ... 20 amp capacity. Safe maximum 16 amps. Buy: 12-2 gauge/ 20 amp 12-3/ 20 amp NMB is house wiring UF is underground Rolls of stranded wire HOOK UP Wires |
White
14 gauge 15 amp 120 volt 15 amp outlet, AFCI, GFCI, timer, switch etc can be installed on 15 or 20 amp breaker. Never connect 15 gauge wire to 20-30-40 amp breaker. ![]() White/ #14 gauge wire, with ground ... 15 amp capacity. Safe maximum 12 amps. Buy: 14-2 gauge/ 15 amp 14-3/ 15 amp NMB is house wiring UF is underground |
50-60
amp breaker use 6 gauge / 240 volt 50 outlet can be installed on 50 amp breaker only ![]() Buy: 6-2 wire Southwire electric tools NMB is house wiring UF is underground |
40-50
amp breaker use 8 gauge / 240 volt 40 amp outlet can be installed on 40 or 50 amp breaker only ![]() Buy: 8-2 wire Southwire electric tools NMB is house wiring UF is underground |
![]() ![]() Copper ground wire. Every device, load, metal enclosure etc must be grounded. Ground wire must be continuous throughout installation, never switched on-off, never used as a Neutral wire. Generally ... use same size as other wire in circuit Buy: 12 gauge copper ground wire Ground wire Green ground wire Ground pigtails Ground rods/ ground clamps at Amazon |
![]() Non metallic flexible cables must carry ground wire, but do not have hazard of short circuit causing injury from shock. Armored steel cable can be used as a grounded connection, and will protect wires from damage. Metal can be energized from an insulation failure. All conduit ...metal, plastic ... flexible and rigid ... must be attached to structure, and attached to enclosures, boxes. Movement, damage and deterioration are major cause of electrical failure. Buy: Non-metallic flexible conduit Power whip Armored cable Southwire armored cable cutter Pull boxes |
![]() Electrical tools must be insulated. Always best to disconnect power, but insulation failure, lack of proper grounding, grounded neutral, lack of GFCI, out-of-code wiring, generator operating without transfer switch, and other problems still pose a risk to anyone working on electric power ... even when breaker is off. Buy: Electrician tools kits KLEIN TOOLS Tools kits IRWIN tools KNIPEX Telephone cable knife Low Voltage Mounting Bracket for Telephone |
![]() 600 volt 12 ga Stranded wire ot THHN wire is good for conduit with multiple wires ... but stranded cannot be installed under screw terminals on outlets, switches, timers etc without risk ... of heat causing splayed strands ....that come loose ... and begin to arc. Connect stranded to short piece of solid copper wire, and attach solid to screw terminal. Do not solder residential or commercial wiring. Project wire, extension cords, thermostat, bell and automotive wire are not rated for residential or commercial wiring. Only wire maked 600 volt can be used for permanent household wiring. Buy: Southwire 600 volt stranded wire Rolls of stranded wire HOOK UP Wires |
![]() Protect wiring from damage Use nipper instead of pliers or screwdriver for removing staples (and nails). Do not damage cable or wires inside cable. -Code says: Cable SHALL BE secured without damage to the outer covering. NEC sec. 336-15 Buy End cutting nippers at Amazon |
![]() ![]() Electrically insulated tools When removing insulation from wire, do NOT score or put cuts on surface of copper wire. Doing so increases resistance and heat on wire and creates possible weak point. Buy tools: KLEIN TOOLS Wire strippers at Amazon Electric Wire Stripping Machine Linesman pliers Utility knife at Amazon |
![]() Multimeters Voltage is tested across two separate wires. Ohms or resistance is tested across both ends of same wire. Amperage is tested along one or two points on same wire. Buy: Analog multimeter Multimeters at Amazon Klein multimeter Electric testers at Amazon Clampmeter for testing amp flow on line |
![]() NEW energy smart |
Why
convert to regular water heater? 1) So water heater can work with any voltage/ connect to 120 volt generator How to connect water heater to generator 2) So you can convert water heater to 120 volts How to convert water heater to 120 volts How to wire water heater thermostats 3) EZ same day repair using generic parts from hardware store How to replace water heater thermostat 4) Less vulnerability to surge/ electronics can blow out with surge How to wire whole house surge protector 5) EZ diagnosis of problem/ buy parts locally .... How to troubleshoot electric water heater 6) No app, no sign-in, no privacy invasion, no pop-ups.... just a plain simple ez-to-fix water heater 7) So you can rewire for simultaneous or off-peak Read off peak water heater thermostats 8) So you can integrate two water heaters using same 30 amp breaker Read two water heaters New government water heater standards 55 gallon walk-in tub 9) So you can integrate with solar Convert water heater to solar DC power 10) So you can add a timer without burning out water heater electronics Water heater timers |
![]() ![]() Note: the wires for thermistor (thermostat) are small. A thermistor is a heat sensitive variable resister. A change in water temperature changes the thermistor resistance (measured in ohms). -The energy smart control board interprets change in resistance as a change in temperature and uses information to activate and deactivate call for heat. This system requires proprietary control board for operation, and is susceptible to surge and voltage anomalies. Ordinary water heater thermostat is mechanical bi-metal switch that bends with heat, and connects and disconnects two points to open and close the circuit. To convert: remove the thermistors, add ordinary thermostat, and re-wire for non-simultaneous operation. Note: all energy smart heaters are non-simultaneous Ordinary residential water heaters are non-simultaneous |
|
![]() ![]() ![]() Cut back foam insulation with wallpaper knife/ wear eye protection. Use same elements that come with tank. Yellow and blue wires going to upper elements from top of tank do not need to be replaced. Blue wire going to lower part of tank may be undersized #14 gauge. The problem with older energy smart: the wires are stranded and not solid copper. Stranded wire is fire risk if not crimped to terminal. Do not put stranded wire under screw plates on thermostats. Do not solder stranded wire ... the heat on wire will melt solder, and cause fire. Use same terminals that are connected to end of yellow and blue wires. Leave small black and red wires in place ... they will not pull out because of foam insulation ... cut back small wires and cap off. The orange wire from top of tank to upper compartment is not needed unless you want to rewire for simultaneous operation (not recommended) or redundant operation (no advantage). So the orange wire inside upper compartment needs to be cut off .... but the end is stranded, not solid copper. Cap off extra orange wire at top of heater so a short circuit cannot energize wire. Since the orange is not long enough to reach right side of thermostat ... do NOT run wire over top of thermostats or elements. Instead use a wire connector and jumper orange wire with short piece of 10 gauge solid copper wire ... do NOT use stranded wire for jumper wire ... use solid copper wire only. Put the solid copper wire under screw terminal on thermostat ... never put stranded wire under a thermostat or element screw ... it will heat up, splay apart and come loose ... cause arcing and connection failure, melting, short etc. Buy: 89T short/ dual-element thermostat Wallpaper knife Yellow 12-10 gauge terminal Wire strippers ![]() Resources: How to wire thermostats Typical water heater set at 120°F ±10% accuracy Bath shower hot-tub temperature 104°F |
![]() |
![]() Crimp terminals onto stranded wire Buy: Crimping tool kit Blue for 16-14 wire Yellow for 12-10 wire Ratcheting Crimper Blue terminals for 16-14 gauge wire at Amazon Yellow 12-10 gauge female terminal 16 pcs |
![]() ![]() Jon, an electromechanical engineer, emailed saying that 'his' energy smart had #14 blue wire between upper and lower elements. He replaced the blue wire with #10 wire. The new wire can be pulled through the insulation after drilling a hole through the insulation. I took the
photograph on the right that
shows lower element on the energy smart at Lowes in 2009. The blue wire
is definitely smaller than the orange wire.
What does this mean? If it is #14, then it would get warm when lower element is energized ... leading to inefficiency. What should you do? Replace with #10 solid copper is best plan. If you leave the #14 blue wire in place, then it is important not to clip off the crimped end on wire, and use it 'as is.' ![]() My response: Stranded wire is a hazard, and cannot be put under a screw plate without risk of failure. As a result, crimped terminals must be used with stranded wire. What should you do? ![]() 1) Keep the existing
factory-supplied
crimp terminal in place ... and install under screw terminals on
element and new thermostat.
2) Snip off the factory crimp terminal and connect the stranded wire to short length of solid copper wire ... cover the connection tightly with twist on connector ... then put the solid copper wire under screw terminal. 3) Hand crimp a terminal onto the stranded wire ... crimp it on very firm ... and pack insulation around it tightly so it won't move. Remember the enemy
of any electrical installation is movement.
|
![]() Clip to hold thermostat/ Thermostat mounting bracket Bradford White part # 239-44479-00/ ![]() Rheem AM23557 The new thermostat MUST sit flat against tank wall or it will not read correct temperature.... thermostat cannot be placed loosely inside the compartment. The clip will hold thermostat firmly in place. Buy: Thermostat clip Adapter kit with thermostat clip |
Do NOT use stranded wire to make
conversion![]() Larger image |
Wiring diagrams for
NEW energy smart with control on front Issues: Remove upper thermostat and upper thermistor located above upper element Must buy upper thermostat and thermostat mounting bracket as shown below The upper thermostat must be covered with insulation when finished Remove lower thermistor located above lower element Must buy upper thermostat and thermostat mounting bracket as shown below The lower thermostat must be covered with insulation when finished The grounding bracket may need to be removed to install bracket to hold mechanical thermostat The mechanical thermostats must sit flat against the tank wall when finished (just like the thermistor must sit flat against tank wall to read correct water temperature) All thermistors and thermostats read approximate temperature. If you have foam insulation... then foam insulation is difficult to cut off precisely All thermostats and elements must be covered with insulation when finished Keep the elements that are provided with tank/ no need to change elements DO NOT USE STRANDED WIRE under screw plates/ crimp terminals onto stranded wire then put terminals under screw plates/ otherwise, use only solid copper wire under screw plates. Reason: stranded wire gets loose under screw terminals when wire gets hot. Solid copper does not. Terminals do not get loose. Loose wires start to arc, causing terminal failure and melted parts. Buy: Dual-element thermostat at Amazon Resources: How to wire thermostats How to replace thermostats Add another thermostat to electric water heater How to test elements How replace elements How to test if power is turned off |
![]() 1) The thermostat clip on lower part of tank is slightly wrong for holding the replacement thermostat. Alterations or innovations might be possible without buying new clip. Thermostat must sit flat against tank and be secured so it does not move. Movement is the enemy of electrical installations and can cause shorts and failures. Buy: Thermostat clip Adapter kit with thermostat clip 2) The insulation needs to be cut away to access the compartment effectively. The insulation and cover plate MUST be re-installed. If thermostat is not covered with insulation and sitting flat against tank, then it will mis-read temperatures and not function as expected ... usually it will cause overheated water. 3) Since at least 2009, wires inside most 240 volt, 4500 watt residential electric water heaters is 12 gauge. Wires coming to water heater from the circuit breaker (overcurrent protection) are required to be larger 10 gauge, with a 30 amp breaker. 12 gauge wire inside the heater is adequate, and does NOT need to be replaced ... however 12 gauge creates inefficiencies since the downsized wire will produce more resistance against the large current of electrons (amperage) that is getting pushed through the matrix (atomic structure) of the wire by 240 volts. Resistance is like friction that causes heat. Higher resistance means more heat loss, which means a trickle of wasted energy that you pay for. |
![]() See larger |
Electric water heater thermostats
are interchangeable Each works with your water heater Temperature for household use Set water heater thermostat temperature to 120°-125° Manufacturer setting was 135° in 2012, and 125° after 2015 to meet new energy standards. Hot tub = temperature 105° Typical shower-bath = 110°F Buy90-150 degree F for residential tank: Water heater thermostats at Amazon Rheem thermostats More thermostats 89T short/ dual-element thermostat All therm-o-disc products Resources: Therm-o-disc 59T-66T sell sheet/ pdf Therm-o-disc thermostats Difference between Rheem thermostats |
![]() ![]() |
Thermostats Therm-o-disc 59T is a generic mechanical thermost. Minimum temperature 90° Maximum 150° High Limit trips at 170° All values +/- 5 Buy 90-150 degree F for residential tank: Rheem UV11698 Rheem SP11698 Camco 08163 Aprom / 110-160° Water heater thermostats at Amazon Rheem thermostats More thermostats All therm-o-disc products Resources: Therm-o-disc 59T-66T sell sheet/ pdf Therm-o-disc thermostats Difference between Rheem thermostats |
![]() ![]() |
Thermostats Buy residential upper and lower thermostats Thermostats are interchangeable/ each works with your water heater Typical residential thermostat ranges: Therm-o-disc: Temperature range 90-150° reset trip @ 170° Apcom: Temperature range 110-160° reset trip @ 180° Temperate range approximate +/- 5° Rated 120, 208, 240, 277, 480 volt AC ... will work with 12-24 and maybe 48 volt DC Calibration range between ON and OFF approximated at 10% 89T is discontinued/ replace with Apcom or Therm-o-disc Buy 90-150 degree F for residential tank: Camco thermostats at Amazon Apcom thermostats Water heater thermostats at Amazon Rheem thermostats More thermostats All therm-o-disc products |
![]() |
Thermostat protectors/
for therm-o-disc upper and lower thermostats Terminal protectors for therm-o-disc Does not fit Apcom style All thermostats are interchangeable Buy Upper element terminal protector Lower element terminal protector |
![]() Larger image |
Thermostat
and element must be covered Cover, insulation and protector are necessary so thermostat can read correct temperature. Thermostats exposed to room temperature will misread temperature and cause overheating. Thermostat must sit flat against tank. |
![]() |
Foam-insulated tank Foam is used to fill cavity between inner steel tank and outer tank shell The foam fits very tight against wire so wires cannot be replaced. Start with 3/8" standard drill bit to drill through steel top. Then use 36" drill bit to drill through foam Drill through top of tank near wiring cavities Keep drill bit near outer edge of tank shell Buy 36" drill bits Fish bit Resource: How to test water heater wires |
![]() ![]() ![]() ![]() |
![]() |
Non-fused
safety switch Cuts power to both legs of 240V circuit. Rated for indoor-outdoor. -3 Hp motor, 17 amps, use 30-60 amp safety switch -30 amp water heater, use 30-60 amp Since water heater is on a breaker, then non-fusible is fine Buy from my affiliate links: 2-pole outdoor / 60 amp/ non-fusible 2-pole outdoor / 60 amp/ non-fusible 2-pole outdoor / 30 amp/ non-fusible 2-pole indoor / 30 amp/ fusible 2-pole indoor / 30 amp/ fusible 2-pole indoor / 30 amp/ fusible Heavy duty safety switches at Amazon |
![]() |
Alternate method Re-wire water heater for PID Insert probe near lower thermostat. Position against tank wall and cover w insulation Wire thermostat and element as shown 240 volt line for water heater MUST be routed through ECO located on upper thermostat. Why? Because ECO is safety device that will cut power to element in event of overheating. PID is powered by 120 volt for example. Hot and neutral are needed for PID. Set temperature controller program. When temperature probe senses cold water, then PID activates contactor Contactor switches 30 amp water heater circuit, and lower element tuns on. Lower element keeps tank hot. This wiring design, both hot wires to element are cut off by contactor. Do NOT connect 240 volt 30 amp water heater circuit to PID... must use contactor Buy PID with relay output and thermocouple/ ITC-100HR/Temperature range 50~250ºC PID Temperature controllers Digital temperature controller 30 amp contactors Solid State Relay Board for Arduino Resources: Contactors Select breaker and wire size Add another thermostat to water heater |
![]() |
Replace short water heater nipple with
brass or stainless steel nipple Use 6 wraps of teflon tape on threads. 6 wraps is standard for all water heater connections, including TP valve and anode rod etc Buy 3/4" x 6" brass nipple 3/4" x 6 stainless nipple (not recommended for softener) Pipe threaders Resources How to maintain water heater |
![]() |
|
![]() ![]() |
Use ordinary 4500 watt foldback
element for older and newer energy smart Buy 4500 watt lifetime at Amazon 4500 watt at Amazon 1-1/2" socket |
![]() ![]() |
Tank rinser Works with ball valve Buy Tank rinser at Amazon Resources: How to replace water heater drain valve How to clean sediment out of water heater How to replace thermostat How to replace element How to maintain water heater Identify water heater valves Advantages/ disadvantages/ Install mixing valve |
![]() |
Prevent rusted water heater/
Inspect and replace anode rod Applies to gas and electric heaters Anode rod prevents steel tank from rusting Remove and Inspect anode each 1-3 years ![]() Standard hex head aluminum anode rod located in separate port on top of tank. Inspect and replace anode rod each 2-5 years to prevent tank from rusting Buy: Aluminum-zinc for longest protection Magnesium for odor control Buy Zinc for odor control Buy anodes 1-1/16 socket Resource How to check anode |
![]() |
Advantages
of power anode: almost 100% Solution for tank
odor, 100%
solution for rusted tank when electric power is ON, tank will not rust
out, anode can be moved to next water heater, can be installed on most
water heaters up to 80 gallon including energy smart, hybrid, some
power vent models .... works for gas and electric water heaters,
includes LED that indicates if power anode working. Buy: Power anode rod |
![]() |
Test pressure Gas and electric Pressure over 80 psi can damage water heater and damage plumbing pipes. Faucets do not last as long, water heater can be damaged Put BTG100 or similar gauge on water heater drain valve. If pressure is high, then install pressure reducing valve. Buy pressure gauges at Amazon Water pressure gauges Watts telltale Water Pressure Test Gauge, 276H300 Telltale pressure gauge is left in place for a day, and marks the highest pressure so user can tell if there are pressure spikes that are causing TP valve to leak water, or other possible problems Resource: Test for low and high pressure on water heater Pressure reducing valve and expansion tank |
What if tank is not
working? Read 'repaired water heater is not working' |
![]() GFCI circuit breaker A GFCI circuit breaker will protect all boxes on circuit Circuit must be grounded. Ground wire must be continuous and connected to each piece of equipment. White wire on circuit breaker must be connected to Neutral busbar inside the breaker panel. Buy GFCI circuit breakers |
Push down![]() 1" wide Push down breaker Plug-in breaker Buy single-pole: Choose from 15 to 60 amp Eaton CL series Siemens 15-60 amp Single-pole tandem breaker Tandem breakers |
Push down![]() 2" wide Push down breaker Plug-in breakers Buy double-pole: Choose from 15 to 125 amp Choose from 15 amp to 200 amp Eaton CL series circuit breaker Siemens circuit breaker Double pole GFCI |
![]() Household NM-B Wires are color-coded so inspectors/ electricians can easily identify which wire is used during construction |
Match
wire size and breaker amp rating If your home was wired by professional electrician who pulled permits, then circuit breaker and wire size will match. If manufactured home or travel trailer has not been altered by homeowner then breaker and wire size will match. If breaker is oversized for wire... fire danger Breaker can let too much electricity travel through the wire. Wire can overheat and cause fire. Call electrician if you suspect wiring is not correct, Absolute electrocution danger when removing cover off main panel. More information below. Main breaker terminals are still Hot when main breaker is turned off. Buy Wire wire at Amazon Resource: Select correct wire and breaker size How to replace circuit breaker |
![]() |
What is 3-phase electric: power plant to end
user Basic house wiring |
![]() | Buy
from my affiliate links every time/ thanks: Amazon As an Amazon Associate I earn from qualifying purchases Enter Amazon from any link on my site, fill cart with any item ... purchases pay small commission E-mail: geno03245w@gmail.com My response might end up in spam folder, check email folders Waterheatertimer on Twitter Message thru facebook |