Home
Search waterheatertimer.org / all results
Search using Find button  

 Tweet button  
What does a pressure switch do?

The vacuum or pressure switch measures the vacuum created by a blower and verifies the blower is operating at speed. How to replace pressure switch
water heater pressure switch Pressure switch / same as vacuum switch What does a pressure switch or vacuum switch do? The vacuum or pressure switch measures the vacuum created by a blower and verifies the blower is operating at speed. When blower is running at correct speed, the pressure switch closes a circuit that can trigger a different operation.

-On a power vented water heater, the vacuum switch is a safety device that prevents possible explosion. If the blower is not running or running too slow, the pressure switch will not close circuit to the gas control valve and water heater will not turn on gas to the burner. This ensures full burning of fuel and prevents explosive gas from accumulating inside vent pipe.

Resource:
Construction, operation, and testing for pressure switch .pdf
How power vent water heater works

The gas valve thermostat senses that water inside tank is below set point and closes a circuit that turns on the 120 volt blower located on top of water heater. -The blower pulls air up through the vent pipe and begins a cycle of releasing toxic combustion by-products, including NO SO CO CO2 and acidic water vapor, into the atmosphere, where it creates an exciting new future for the planet . Alternative for some: Connect solar panels directly to electric water heater
-The vacuum safety switch is connected to blower via rubber tube. The rush of air through the vent pipe creates vacuum pressure. At beginning of a call for heat, the vacuum switch is OPEN. The vacuum switch must close, like an ordinary on-off switch and complete a circuit that notifies gas control that blower is operating correctly. -The vacuum or pressure switch measures the vacuum created by the blower and verifies the blower is operating at speed. This ensures the blower can evacuate combustion gasses and support complete burning of fuel. This prevents explosion hazard caused by ignitable fuel gathering in vent pipe. The efficiency of gas water heater combustion is typically 60-61%, with remaining 39-40% of heat going up the flue pipe. Calculate efficiency

-The blower has a resettable thermal safety switch that monitors vent temperatures. If temperature on vent pipe exceed 180°, the thermal switch cuts off power and blower stops running. The vacuum switch resets to open position and gas valve thermostat turns off gas supply. -If temperature of water inside tank exceed high limit set point of thermostat, then gas control valve turns off all gas. The gas control valve may require replacement. Some gas control valves can be reset once repairs have been made to correct cause of overheating. If the thermostat comes out of calibration, and is no longer performing, it requires replacement of gas control valve
-When temperature inside tank reaches the set point, for example 120°F, the gas control valve thermostat turns off all power, and the water heater goes into standby mode until water temperature drops below thermostat set point again.

Generally, to check if blower is good and pressure switch is bad, you bypass the pressure switch and connect blower directly to 120 volt outlet, running a pigtail to the blower or plugging blower directly into outlet.
"In troubleshooting pressure switches, you usually just jumper across it so it looks like a solid wire to the control.  Do this only when the unit is trying to fire up, so it is in the correct sequence. ~~ If you get no continuity however, it sounds like the contacts in the switch are shot and the switch should be replaced. Jumpering across it will let you know if that is what's keeping the heater from firing up. Do NOT leave the jumper in place as you're disabling a safety device." Source

Pressure switches fail when a few drops of water condense in the small tube the connects to the switch, or some other internal problem with contacts happens.  Using a volt meter on the switch while gently blowing /sucking on the tube will confirm it's operation... or lack of operation.
Pressure switch troubleshoot
Test pressure switch
Air pressure switch testing
Intellivent wiring
Pressure switch replacement
Bradford White pressure switch replacement
Check pressure switch

Resources:
How to troubleshoot gas water heater
Troubleshoot power vent water heater
"How to check the vacuum line
Requires the use of a magnahelic gauge.
1. Place inline “T” fitting between vacuum switch and vacuum line from the blower motor.
2. Turn heater on and adjust so water heater turns on. Blower motor turns on..
3. Check  pressure on the magnahelic gauge. If gauge shows 0.6 to 1.5 inches water column, then blower motor is inducing the proper draft and vacuum lines are not obstructed.
4. If gauge does not read between 0.6 and 1.5 inches water column -
a. Move the inline “T” fitting and place it between the blower motor and the vacuum tube at the top of the heater.
b. Check the pressure on the magnahelic gauge. If the gauge shows 0.6 and 1.5 inches water column, then the blower motor is inducing the proper draft and vacuum lines are obstructed. Replace the heater.
 c. If the gauge does not read between 0.6 and 1.5 inches water column, then the blower motor is not inducing the proper draft. Replace the blower motor."  Resource: Power vent troubleshoot / pdf
Buy: magnahelic gauge
water heater pressure switch Pressure switch/ Vacuum switch for water heaters
There are 3 major water heater manufacturers, AO Smith, Bradford White, Rheem, that make all the other brands from Kenmore, Craftmaster, Whirlpool, American, Reliant (AO Smith) to Reliance (Rheem)
Buy water heater pressure switch:
Rheem water heater pressure switch
Bradford White pressure switch
AO Smith pressure switch

Resource:
Pressure switch replacement
Bradford White pressure switch replacement
water heater blowers Blowers: Fasco, AO Smith, Bradford White, Rheem power vent water heater exhaust draft-induced blowers
Buy blower:
Water heater blowers at Amazon
Other types blowers
Fasco multi-purpose blowers
AO Smith multi-purpose motors and blowers
Furnace blowers
14 things needed for gas water heater & .pdf resources
What you need for operation of gas water heater.
General troubleshoot
1) Basic parts and operation
2) Adequate incoming air supply ... issues: closed doors, tightly insulated house, very hot attic.
3) Adequate air supply getting to burner... issues: dirty vent screen, dirty environment, maintenance.
4) Thermal cutoff  ... TCO ... issues: failed part, maintenance, vent.

5) Flammable vapor lockout .... issues: exposure to vapors, bad FV sensor, failed FV system,
6) Fuel supply to gas valve thermostat ... natural gas and propane are different ... issues: wrong gas, low pressure, moisture in pipe, undersized gas meter, supply line too small for BTU rating.
7) Gas valve thermostat regulates fuel supply ... issues: not enough gas, failed thermostat, failed gas control valve.

8) Fuel supply from thermostat to burner ... issues: maintenance, thermocouple-thermopile, gas control valve.
9) Clean and replace burner ... issue: periodic maintenance requires burner inspection, cleaning, and possible replacement

10) Functioning thermopile-thermocouple-pilot light ... issues: misalignment, failure of part.
11) Ignition of fuel supply by pilot light or hot surface igniter ... issues: pilot light, piezo igniter, electrode.

12) Power vent water heater troubleshoot ... issues: pressure switch, blower, blower sequence from gas control, outlet polarity
13) Venting combustion byproduct .... issues: vent in disrepair, other vents in house drawing air

14) Misc troubleshoot manuals

Gas and electric water heaters Support the economy:
Buy water heaters from my associate links:

50 gallon Gas water heaters at Amazon
40 gallon gas water heaters at Amazon
50 gallon Electric water heaters at Amazon
40 gallon electric water heaters at Amazon
Hybrid / heat pump/ water heaters at Amazon

Resources:
How to install gas water heater
How to install electric water heater
Troubleshoot gas water heater
Troubleshoot electric water heater
Point of use water heaters
Resources:
Troubleshoot Gas valves with manuals
Icon gas valve

How to replace water heater element Waste King disposal
How to wire tankless electric


Install point of use water heater
Titan tankless

Contactors/ relays
Type 1 and type 2 surge protection surge protection
Programmable timers

Woods timers
surge protection
Anode rods anode rods
Recirculation system

Tankless recirculation
Point of use water heater
Install and troubleshoot garbage disposal Waste King disposal
Buy
Electronic parts

Industrial supplies

Tools and home improvement

Home and garden

Hayward pool
Pentair pool

Southwire electric
Buy
Tools

DEWALT
Black and Decker
Stanley
SKIL
Makita
Porter-Cable
Bosch

Irwin Hand tools
Klein hand tools
Fluke electrical testing
Dremel hobby tools

Campbell Hausfeld air powered
Tekton automotive

Powerbuilt automotive
Saws and saw blades
box timers Resource:
Compare box timers
DPDT timers
Intermatic
Control water heater w/ Z-wave
Intermatic control centers Resource:
Intermatic control centers: and parts
Digital control centers and parts
Tork control centers and parts
Subpanels
All control centers and parts
Enclosures
programmable timer Resource:
Programmable timers
Countdown timers
Off delay timers
On delay timers
Timer modules
Din rail
Twin & one-shot
Woods
Intermatic
Tork
Low voltage power packs Recirculation systems
Buy from my affiliate links every time/ thanks:
Amazon
As an Amazon Associate I earn from qualifying purchases
Enter Amazon from any link on my site, fill cart with any item ... purchases pay small commission

E-mail: geno03245w@gmail.com
My response might end up in spam folder, check email folders
Waterheatertimer on Twitter
Message thru facebook