Wiring
for other models Resource:
T104
& T174 wiring
T103
& T173 wiring
T101
& T171 wiring
T101B
wiring
T102
& T172 wiring
T105
& T175 wiring
T106
& T176 wiring |
Wiring
for other T100 series timers
|
Detail below |
T-101
timer 120Volts
Resource:
T101
series
T171
skip-a-day series
T101R201 manual
T101P201 manual
Sell sheet with model numbers
Replacement clock motor
T100
series repair parts
How to operate and set T101 timer
How to find Hot wire
Pool timers
|
 |
T-101
timer 120Volts
T-101
timer for 120 Volt water heaters
T-101 SPST [single-pole single-throw]
Black Hot
wire must connect to pole 1.
Neutral must go to pole A
Black to Load goes to pole 2
White to Load goes to pole A
|
Larger image |
T-101
timer controls 3-phase
Use T101 120Volt timer to control 3 phase loads.
use wiring diagram above to control 3-pole contactor, or diagrams to
left and right
Neutrals connect to terminal A
Hot from breaker connects to terminal 1
Hot to contactor connects to terminal 2
No fuse required on incoming line.
Fused disconnect required on 3-phase line and timer in most commercial
applications
Resource:
More 3-phase timers |
Larger image |
|
|
T-101
timer 240 Volts
Convert T101 into T102 timer to control 240Volt load:
Replace 120volt WG1570 clock motor with WG1573 clock motor. Connect new
clock to same terminals A and 1.
240V: L1 Hot from breaker connects to terminal A; L2 Hot from breaker
connects to terminal 1
240Volt wires going to Load connect to terminals A and 2.
T-101 changed to 240 V (207-277)
Buy:
WG1573 for 60 Hz 208-277V Amazon
|
|
|
 |
T101 timer is fully repairable
Resource:
How to take apart and repair T100 series
timers |
 |
T-101 clock motor 120 V
Buy:
WG1570 for 60 Hz 120 volt Amazon |
T-101 clock motor 120 V
Buy:
WG1570 for 60 Hz 120 volt Amazon |
Change
T101 timer to different voltage
by
changing clock motor
>>>>>
|
T-101 changed
to 24 volt
CW190-10 for 24 volt 60 Hz 24V at Intermatic |
T-101 changed to 240 V (207-277)
Buy:
WG1573 for 60 Hz 208-277V Amazon |
T101 changed to
60Hz to 50 Hz
WG1571-10D motor for 50 Hz 120Volt |
T-101 changed to 480 Volts
Buy:
WG1576 for 60 Hz 480V at Amazon |
How to replace Intermatic clock motor |
 |
Trippers
Dial can have 12 sets ON-OFF trippers
Buy:
156T1978
trippers Amazon |
Larger image
 |
Insulators
-Keep insulator over screw
terminals to prevent accidental electrocution hazard.
Insulator pushes down over two knobs located on timer mechaism below
the yellow dial.
Translucent
124T1948 single pole T101, T102, T105
124T1948 single pole T171, T172, T175
Buy:
124T1948 at Amazon
Black rigid
124T2411A rigid
Buy:
At Amazon
|
 |
Convert
indoor timer into outdoor timer:
Buy
different enclosure.
Use thumb spring located top inside timer to remove mechanism from
enclosure
Buy:
2T2502GA beige plastic Outdoor box at Amazon
Resource
More enclosures |
 |
Installation tips
-Secure wire or conduit to enclosure. All wires, enclosures and conduit
must be secured to structure.
-Always use solid copper wire under timer screw terminals ... stranded
wire can come loose and cause fires.
-Keep enclosure door closed to prevent possible fire hazard from
spreading.
-Keep insulator over screw terminals to prevent accidental
electrocution hazard.
-Install enclosures away from hazards such as lawn mower or machinery.
-Install outdoor boxes in sheltered area if possible and 12" above
anticipated snowfall.
-For safety, make sure Load is grounded correctly. People often forget
to securely join the ground wires inside timer because wire sometimes
gets a bit short. Buy extra length of wire from box store. Load must be
grounded. Why you need ground wire |
 |
Use correct wire and breaker
Oversized is OK, undersized is hazard
Look at label on load to determind correct size wire and breaker
Watts divided by volts = amps
If Load is 120 volt, and watts is 1500 = 12.5 amps.
Next calculate 80% safe maximum. 20 amp breaker x .80 = 16 amps safe
maximum
15 amp breaker x .80 = 12 amps safe maximum
The calculation shows that 4500 watt load requires 20 amp breaker and
12 gauge wire up to 150 feet.
Longer distance, use larger wire and breaker.
Buy
from my affiliate links:
Southwire
cable and tools
Resource:
Figure volts amps watts |
T101B
Wiring begins here
Applies to T101B with
separate wiring terminals |
 |
|
|
You
can accomplish same wiring using T104 timer & change clock motor
You
can accomplish same wiring using T103 timer |
|
T-101B clock motor 120 V
Buy:
WG1570 for 60 Hz 120 volt Amazon
T-101B change to 208-277
Change T101B timer into 240 Volt
Buy:
WG1573 for 60 Hz 208-277V
T-101B change to 480 Volts
Change clock motor to WG1573
Buy:
WG1576 for 60 Hz 480V at Amazon |
Change clock motor
voltage
>>>>>
|
T-101B change to 24 Volts
CW190-10 for 24 volt 60 Hz 24V at Intermatic
T-101B change
from 60Hz to 50 Hz
WG1571 motor for 50 Hz 120Volt at Intermatic |
